What is the torque for Harley primary cover?
Your torque wrench should be set at 84-108 inch-pounds of torque. Remember to tighten them in a star pattern much like the lug nuts on a car tire.
What is the torque specs for derby cover on Harley?
The derby cover torque specs are 84-108 in lbs.
How tight should derby cover?
Just snug them up. The really important thing is not to over tighten them! They are only keeping the gaskets compressed.
What are the torque specs for Harley Davidson?
The torque of Harley Davidson Road King is 150 Nm @ 3250 rpm.
How often should you change the primary fluid in a Harley Davidson?
every 10,000 miles
It is recommended to change the oil at 1,000 miles, then every 10,000 miles after that.
What is torque on the rear axle nut of a Harley-Davidson?
60 – 65 ft-lbs torque
Tighten rear axle nut to 60 – 65 ft-lbs torque.
How much HP do Harleys have?
The Harley-Davidson produced 73.66 peak horsepower at 4,860 rpm and has a very linear, rider-friendly delivery on the way there. Note the torque curve’s usability as it shoots up from 1,300 rpm and steadily climbs to its 98.39 pound-feet peak output at 2,790 before beginning to taper off at 3,000 rpm.
Can you use ATF in Harley primary?
We submit that ATF is too thin for Harley primary use. It’s true that many Harley riders have had years of problem-free performance with ATF. We contend that a thicker oil will provide superior metal-to-metal wear protection. Chains and sprockets will last longer using a fluid with an appropriate viscosity.
Can I use 20 50 oil in my Harley primary?
A particularly nice feature about AMSOIL 20W-50 Synthetic Motorcycle Oil is that it can be used in the engine, transmission and primary chaincase of Harley-Davidson motorcycles.
What oil goes in a Sportster primary?
My wife’s Sportster Forty-Eight calls for 20W-50 and that’s what I use for the engine and primary/transmission. My oil of choice is Amsoil and the others are great too . . . it comes down to personal preference.
What kind of oil goes in Harley primary?
The optimum product would be Mobil 1 Racing™ 4T 10W-40 motorcycle oil, but it is also okay to use Mobil 1™ V-Twin 20W-50.
What is the axle nut torque spec?
Generally, jam nuts less than 2-5/8″ should be torqued to 200-300 lbf-ft; nuts 2-5/8″ and over should be torqued to 250-400 lbf-ft. See chart for exact torque specification. The final step is to use a dial indicator to verify the end play or free movement of the tire and wheel assembly along the spindle axis.
Why are Harleys so low power?
One of the reasons that Harleys have low horsepower is because they’re built for cruising. Cruising is when you ride your bike at a slower speed for an extended period. This allows you to enjoy the scenery and take in the experience without worrying about being on the road too long.
What are the torque specs for the primary cover bolts?
You need a manual, as you need torque specs for the entire assembly of the primary cover, inner primary bolts, clutch hub nut, compensator, starter bolts, starter jackshaft bolt, swingarm pivot bolts and rear axle nut. 1.) Primary cover bolts: 14-21 ft lbs
What are the torque specs for the clutch bolts?
torque specs. 1.) Primary cover bolts: 14-21 ft lbs. 2.) Inner primary bolts: 18-24 ft lbs. 3.) clutch hub: (left hand thread) 55-60 ft lbs. 4.) compensator: 150-165 ft lbs. 5.) starter bolts: 24-28 ft lbs.
Is there a torque spec for the rear Cam?
Its also not a torque spec, rather a tolerance spec related to/for gear lash, as the drive gear I’d mounted to the crank and runs the rear cam. In addition to what has been said about torque specs.