How does OSHA define a catastrophe?
The hospitalization of three or more employees resulting from a work-related incident or exposure; in general, from an accident or an illness caused by a workplace hazard.
What are the types of OSHA violations?
There are six specific categories of OSHA violations, each of which carries either a recommended or a mandatory penalty.
- De Minimis Violations.
- Other-than-Serious Violations.
- Serious Violations.
- Willful Violations.
- Repeated Violation.
- Failure to Abate Prior Violation.
What is OSHA imminent danger?
The threat must be imminent or immediate. This means that you must believe that death or serious physical harm could occur within a short time, for example, before Cal/OSHA could investigate the problem.
Who must report to OSHA any accident results in death of an employee or the inpatient hospitalization of three or more employees?
Employers are required to report, within 8 hours after their occurrence, incidents which result in a worker fatality or multiple hospitalizations.
What is a fat cat OSHA inspection?
The Fatality/Catastrophe Report in OIS (FAT/CAT) is an unprogrammed activity (UPA) intake form that must be completed for all fatalities or catastrophes unless knowledge of the event occurs during the course of an inspection at the establishment involved.
How does OSHA investigate a death?
If the death has already occurred, then the OSHA compliance office must complete a fatality investigation inspection to identify whether the employer is at fault for the death due to an OSHA standard violation.
What type of OSHA inspection is conducted when immediate death?
imminent danger inspection
What Type of OSHA Inspection is Conducted When There’s an Immediate Death? When immediate death or serious harm is likely, an imminent danger inspection takes place. However, if an immediate death has occurred, it must be reported, and a fatality inspection must take place.
What qualifies as imminent danger?
An imminent danger is a workplace hazard that puts you at immediate serious risk of death or serious physical harm. It may be a safety hazard such as an unstable trench or exposed electrical wire that could cause a serious or fatal accident immediately under present conditions.
What are OSHA reporting requirements?
All employers are required to notify OSHA when an employee is killed on the job or suffers a work-related hospitalization, amputation, or loss of an eye. A fatality must be reported within 8 hours. An in-patient hospitalization, amputation, or eye loss must be reported within 24 hours.
What are the reporting requirements for a death in the workplace?
Cal/OSHA regulations require that employers must report any Serious Injury/Illness or Fatality to the nearest Cal /OSHA District Office. practically possible but not longer than 8 hours after the employer knows or with diligent inquiry would have known of the serious injury or illness.
What is the role of the safety and health professional with regard to handling employees who might be drug or alcohol abusers?
What is the role of the safety and health professional with regard to handling employees who might be drug or alcohol abusers? Safety and health professionals should be aware of the workplace problems that can be caused by alcohol and drug abuse.
What are OSHA fat cat reports?
What type OSHA inspection is done after a death?
What Type of OSHA Inspection is Conducted When There’s an Immediate Death? When immediate death or serious harm is likely, an imminent danger inspection takes place. However, if an immediate death has occurred, it must be reported, and a fatality inspection must take place.
What are the 4 types of OSHA inspections?
Types of OSHA Inspections
- Imminent Danger Inspections.
- Investigative Inspections.
- Employee Complaint Inspections.
- Programmed Inspections.
- Follow-up Inspections.
Who provides the fat test report?
The manufacturer provides FAT test report upon completion of the test. It is the inspector responsibility to review the test report and match measured value against acceptance criteria indicated in the approved procedure or datasheet. FAT Test for Rotary Equipment
What is fat test in manufacturing?
Factory Acceptance Test (FAT Test) The factory acceptance test (FAT) refers to the functional test that is performed by the vendor upon completion of the manufacturing process to prove the equipment has the same specification and functionality that indicated in the datasheet, specification and purchase order.
What is the fat test in a compressor?
FAT Test in Compressor. Similarly, the compressor performance test and mechanical running test are done on the same day and can be considered as a FAT test. Obviously, casing inspection, impeller and rotor “high speed test” and dynamic balancing test are done prior to the FAT test. FAT Test in Gas or Steam Turbine.
What are the different types of fat tests?
Normally pump performance test, net positive suction head test (NPSH Test) and mechanical running test are done in one visit and can be categorized as FAT test. Obviously, the pump casing inspection, impeller, and rotor dynamic balancing test are done before FAT Test.