What sizes does T1-11 come in?
You can find T1-11 siding in sheets that are 48 inches x 96 inches or 48 inches x 120 inches. It comes in thicknesses of 3/8 of an inch, 5/8 of an inch and 3/4 of an inch.
How wide is T1-11 siding?
x 4 ft. x 10 ft.; Actual: 0.593 in. x 48 in.
Can T1-11 be hung horizontally?
T1-11 siding is typically installed vertically to give a look reminiscent of board and batten siding, but it can be install horizontally though that is rarely done.
Should you nail or screw T1-11 siding?
T1-11 siding is designed for installation on framing with standard 16-inch spacing. You can attach them with exterior screws or galvanized nails.
Do you need sheathing under T1-11?
Structurally rated 7/16” or thicker T1-11 siding can be fastened directly to the exterior face of studs at 16” centers and can act as both sheathing and siding in one. T1-11 siding 3/8” or less in thickness isn’t rated as structural and will require sheathing underneath it.
What is better than T1-11?
LP SmartSide is an engineered wood product that is more weather-resistant than T1-11 siding. It is less susceptible to rot, fungal decay, insect damage and thus requires less maintenance. LP SmartSide is, overall, a better cladding solution for most people.
Is T1-11 waterproof?
This type of plywood siding is injected with rosins and other chemicals, under pressure, to make it waterproof and protected against termites, rot, and fungal decay. It is the best version of T1-11 siding as it lasts considerably longer. Both Plywood and OSB T1-11 siding should be treated or primed.
What does a sheet of T1-11 cost?
The average cost of T1-11 siding is $2.25 per square foot to $6 per square foot for material costs.
How long will T1-11 siding last?
T1-11 siding is a very durable siding material and can last for more than 20 years if it is properly installed, regularly maintained, sealed with quality paint or stain, and protected from water and mold damage.
Can I use screws on T1-11 siding?
Exterior grade or treated screws can be used to fasten T1-11 panels provided they meet the minimum code requirements. A #8 1-7/8” screw is equivalent to a 6d nail, and #8 2-1/2” screws are an alternative to 8D nails.
Should I caulk T1-11 siding?
The top T-111 panel should be installed about 1/4 inch off the shelf formed by the flashing to prevent moisture from wicking up into the wood. This is especially important when using engineered siding. If the siding was installed with Z-flashing, do not caulk in the grooves.
Does T1-11 need to be painted?
Personalization. The other downside of OSB T1-11 is you can’t stain this siding. It must be primed and painted, taking away one of the primary reasons homeowners choose to go with this particular siding material.
What is better than T1-11 siding?
It can stand up to harsh weather in any climate and resists damage from termites and fungal decay. How to Decide: If you want the most durable siding available, then LP wood siding is your better choice. If you want to sacrifice some durability for savings, then choose the plywood grade over the OSB T1-11.
How do you nail T1-11 siding?
The typical nailing pattern for T1-11 siding is similar to that of fastening any type of plywood panel. Every 6” on the sides and every 12” on the studs located in between, the edges at the sill and top plate should be nailed every 4” to seal tight against insects and air.
How to install T1-11 siding?
1.. Wrap the house with house wrap or 15 mil tarpaper. Staple the material to the studs with a staple gun and cut…
How to install T1 11?
How to Install T1-11 Siding. T1-11 plywood is an economical siding choice for sheds and houses. The 4-by-8-foot, 5/8-inch sheets come with a solid or grooved surface, and the long edges are
What is the best plywood for siding?
– When fiber-cement siding is compared to other types of siding, fiber-cement is considered the more premium product and tends to garner better resale value for a home than vinyl and – Fiber-cement siding resists fire. – Since fiber-cement siding is thick, it closely mimics real shiplap wood siding.
How do you install plywood siding?
– Start to finish 1 day – Difficulty Hard – Involves Sawing, Drilling, Measuring