Does THOROSEAL come in colors?
Coverage will vary depending on surface texture and porosity. White and standard gray (this color is not uniform) Custom and landscape colors are available for 5,000 lbs (2,268 kg) minimum order.
How many coats of THOROSEAL?
Just clean the surface of dust and other particles before application. Next, add 1.5 liters of water for every can and shake the can well. Then apply two coats on the surface. The first coat should be applied horizontally.
What does THOROSEAL do?
Thoroseal is a building product manufactured by BASF Construction Chemicals. It is a waterproof cement-based coating that is used to fill, seal and protect interior and exterior surfaces. It is resistant against weather erosion and can be used to protect concrete, brick, building blocks and other materials.
How much THOROSEAL do I need?
A two layer application will require a minimum of 2,5 kg powder per m². Note that the quantities required may increase by up to 50% on rough substrates. 25 kg sack. THOROSEAL should be stored under cover and clear of the ground.
Is Thoroseal waterproof?
MasterSeal 581 (formerly Thoroseal) is for concrete and masonry and resists both positive and negative hydrostatic pressure. It is a cement based waterproofing for Interior and Exterior, above and below grade, with a high quality finish suitable for architectural coatings, and is NSF 61 Potable Water Certified.
What type of waterproofing is Thoroseal?
cementitious waterproofing
Choose where to buy SuperThoroseal is a cementitious waterproofing intended for use on cement-based surfaces. Super Thoroseal is a blend of Portland cements, selected aggregates and spray polymer modifying agents. The best type of waterproofing for use on concrete surfaces is a cement-based material.
How long does Thoroseal take to dry?
Allow to cure 24 hours, then apply the second coat and finish with a vertical stroke. Above grade, the second coat can be replaced with a Thoro® high- build architectural coating to achieve better color uniformity.
How long does Thoroseal take to cure?
Allow Thoroseal® Foundation Coating to cure 7 – 10 days before immersion in water.
How long does it take for Thoroseal to dry?
Use a tampico fiber brush to apply Super Thoroseal® in a thick coat, working the mixture into the pores of the surface for a good penetrating seal. Double back and use the brush to smooth out the material. Allow 12 hours between coats for drying time.
How do you apply Thoroseal waterproofing?
Start at the top and work down. Use a tampico fiber brush to apply Super Thoroseal® in a thick coat, working the mixture into the pores of the surface for a good penetrating seal. Double back and use the brush to smooth out the material. Allow 12 hours between coats for drying time.
Can you seal concrete to make it waterproof?
After you complete a concrete job, don’t neglect the single most important step to ensure that it lasts a lifetime: sealing. With a high-quality sealant—and this helpful guide—you can waterproof and protect your new concrete surfaces for years to come.
What is thoroseal coating?
Thoroseal® is a Portland-cement- based coating for concrete and masonry that resists both positive and negative hydrostatic pressure. Polymer-modified with Acryl 60®, Thoroseal® creates a low- maintenance and highly durable waterproof barrier.
Do you need a top coat for thoroseal?
With any cementitious product, such as Thoroseal®,it may be difficult to achieve color uniformity due toweather and substrate variability. For this reason, itmay be necessary to apply a topcoat of a Thoro®architectural coating.
What is the application rate for thoroseal?
2. A 3 lbs/yd2 (1.6 kg/m2) application rate doesnot eliminate surface irregularities such as struckmortar joints. To hide surface irregularities, sprayand back-brush a base coat of Thoroseal®at.
How do you mix acryl 60 and thoroseal?
blend of Acryl 60®diluted with water. Maximumdilution ratio is 1 part Acryl 60®to 3 parts water.Approximately 6 quarts of mixing liquid is neededper 50 lbs of Thoroseal®powder. Up to 2 additionalquarts of mixing liquid may be added when using as.