What size is #8 JIC?
JIC 37° Flare (SAE J514)
| Inch size | Dash size | Male Thread O.D. (in) |
|---|---|---|
| 1⁄2 | -8 | 0.75 |
| 5⁄8 | -10 | 0.88 |
| 3⁄4 | -12 | 1.06 |
| 7⁄8 | -14 | 1.19 |
What does JIC mean in fittings?
Joint Industry Council
JIC (or Joint Industry Council) fittings, defined by SAE J514, are compression fittings machined with a 37 degree flare seating surface and parallel threads. They are commonly manufactured in nickel alloys, brass, carbon & stainless steel.
What size is a JIC fitting?
JIC fittings are dimensionally identical to AN (Army-Navy) fittings, but are produced to less exacting tolerances and are generally less costly. SAE 45-degree flare fittings are similar in appearance, but are not interchangeable, though dash sizes 2, 3, 4, 5, 8, 10, 14, and 16 share the same thread size.
What are JIC standards?
JIC fittings, defined by the SAE J514 and MIL-DTL-18866 standards, are a type of flare fitting machined with a 37-degree flare seating surface. JIC (Joint Industry Council) fittings are widely used in fuel delivery and fluid power applications, especially where high pressure (up to 10,000 psi) is involved.
What size is #8 hydraulic hose?
How to Interpret Hose, Tube & Fittings “Dash Sizes”
| HOSE I.D (Inches) | ||
|---|---|---|
| All EXCEPT Transportation & Refrigerant Hoses | ||
| -6 | 3/8 | 10 |
| -8 | 1/2 | 12,5 |
| -10 | 5/8 | 16 |
What size is SAE 8?
dash 8 means 1/2″ ID in hoses but means 1/2″ OD on steel tubes. SAE can mean O-ring face seal or it can mean O-ring boss, or it can mean J.I.C. as well. In both J.I.C. and O-ring Boss, it will mean 3/4″ fine threads, or 16 threads per inch.
How do I know if I have a JIC fitting?
4.Identifying the thread by gauge In a word,if the fittings has a 37° flare (sealing surface angle)and straight United National Fine straight Threads (UNF) after inspection. It can be identified be JIC fitting.
What size is a #6 hydraulic fittings?
3/8-18
From the hydraulic catalog, the fitting can be identified as a NPTF/ MALE/SWIVEL. The -6 fitting has 3/8-18 threads, which can be identified using the calipers, thread gauge and the following tables.
How do I know if my JIC fitting?
Four steps to know if your fittings are JIC:
- Identify if the thread is parallel or tapered. NPT/NPTF and BSPT are tapered threads while UN/UNF and BSPP are parallel.
- Determine the flare angle by using a calipers.
- Determine the thread diameter.
- 4.Identifying the thread by gauge.
What size hose is 8 an?
1/2″
Russell Performance Technical Support
| AN Size | Metal Tube O.D. | Thread Size |
|---|---|---|
| -5 AN | 5/16″ | 1/2″ – 20 SAE |
| -6 AN | 3/8″ | 9/16″ – 18 SAE |
| -8 AN | 1/2″ | 3/4″ – 16 SAE |
| -10 AN | 5/8″ | 7/8″ – 14 SAE |
What is SAE 8 port size?
What size is 8 an fitting?
AN Fittings and Hose Sizes Chart
| AN Size | Hose / Tube O.D. | SAE Thread Size |
|---|---|---|
| -6 | 3/8 in. | 9/16 in.-18 |
| -8 | 1/2 in. | 3/4 in.-16 |
| -10 | 5/8 in. | 7/8 in.-14 |
| -12 | 3/4 in. | 1 1/16 in.-12 |
What thread is SAE 8?
What thread is JIC?
JIC – Joint Industry Council Thread – SAE JIC 37° Commonly referred to as just JIC fittings these metal to metal sealing type fittings have a 37° flare (sealing surface angle) and straight United National Fine straight Threads (UNF).
What thread pitch is JIC?
37° flare
Commonly referred to as just JIC fittings these metal to metal sealing type fittings have a 37° flare (sealing surface angle) and straight United National Fine straight Threads (UNF).
ARE AN and JIC fittings interchangeable?
It’s important to note that the AN and JIC specifications are no longer in existence in most cases. The majority of the hydraulic population agrees, the JIC (or SAE) 37 degree fittings are generally interchangeable with AN fittings.
What size hose is 10 an?
5/8″
Russell Performance Technical Support
| AN Size | Metal Tube O.D. | Thread Size |
|---|---|---|
| -8 AN | 1/2″ | 3/4″ – 16 SAE |
| -10 AN | 5/8″ | 7/8″ – 14 SAE |
| -12 AN | 3/4″ | 1-1/16″ – 12 SAE |
| -16 AN | 1″ | 1-5/16″ – 12 SAE |