What does ignition lockout mean on pool heater?
Pool heater ignition lockout is designed to protect against overheating. Of course this is a good thing, but if owners are not able to clear the lockout and reset their digital equipment, the situation can go bad fast.
How do you fix the ignition lockout on a carrier furnace?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
What causes ignition lockout on furnace?
Common causes of furnace lockouts are a defective igniter or defective flame sensor. When the furnace attempts to start, sensors check for igniter action and the presence of flame. If the igniter doesn’t activate within a few seconds, the furnace controller stops the ignition sequence.
How do I get my oil furnace out of lockout mode?
Though lockout mode errors and resets do vary from manufacturer to manufacturer, most use a simple reset procedure that involves turning power off to the furnace for thirty seconds or longer and turning it back. The interrupted power supply clears the lockout and will allow the unit to attempt normal operation again.
What does ignition lockout mean?
#2 – Ignition Lockout If you experience an ignition lockout, your boiler has probably attempted to fire up 3 times — and failed. If this happens, you’ll see an ignition lockout fault on the boiler’s display.
How do you unlock a pool heater?
How to Reset the Lockout on a Pool Heater
- Reset the breaker for the electrical circuit to the pool heater by flipping the breaker switch to the “Off” position and then to the “On” position.
- Remove the cover on the digital control panel.
- Press the “Mode” button, and cycle to the “Standby” setting.
What does lockout mean on a oil furnace?
has effectively shut down
Boiler lockout is a term used by boiler manufacturers to mean that the boiler has effectively shut down. When a boiler has a fault, ‘lockout’ prevents further damage. If you look on the front of your boiler you will usually see a reset button. Your instruction manual will say to press this to reset the boiler.
What causes oil burner lockout?
A boiler can lock out for several reasons, such as you’ve run out of heating oil, there’s been a power cut, low pressure or a more serious safety issue. Another cause could be an extreme change in boiler pressure, this may occur with a sludge blockage.
How do I lock my pool heater?
Use the “Up” and “Down” buttons to set the desired maximum temperature lock. Typically, the maximum lock temperature is two or three degrees higher than the desired water temperature. Press the “Mode” button, and the heater will return to “Standby” mode.
Where is the reset button on my carrier furnace?
To reset the furnace, press and release the raised red button at the center of the flame roll-out switch. 30 minutes between each reset is allowed, and you can press the button up to three times.
Can you lock the pool heater?
Heater control panel lockout – To prevent unwanted adjusting or manipulating of the heater settings, the control panel can be locked. Once locked, if any button is pressed, the display will read: To activate the control panel lockout, press the MENU SELECT and MODE buttons simultaneously.
Where is the reset button on a carrier furnace?
Press and release the raised red button at the center of the flame roll-out switch to reset the furnace. You can press the reset button up to three times before troubleshooting the furnace’s internal components or calling for repair service; allow 30 minutes between each reset.
How do you manually reset a carrier furnace?
How To Reset A Carrier Furnace
- Locate your thermostat and turn it down to prevent it from triggering the need for heat from the furnace.
- Turn off the breaker switch that supplies power to your furnace, or you can unplug the furnace.
- Wait for 30 seconds.
- Turn the breaker switch back on or plug your furnace back in.
Why do I have to keep hitting the reset button on my oil furnace?
Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. Make sure to clean the air filters and keep enough vents open so the furnace has enough air to operate and clean the blower wheel as well.