How do I access my HP 1810 switch?

Posted on by David Darling

How do I access my HP 1810 switch?

Open the web browser on the PC, and enter the switch factory-default address, http://192.168.2.10, to access the switch’s web interface. Click Log on to log onto the switch (by default, there is no password).

How do I change the IP address on my HP switch?

WebAgent: configuring IP addressing

  1. In the navigation pane, click on Home.
  2. Click on Quick Setup.
  3. In the Switch Quick Setup Parameters box, click on Change.
  4. Enter the IP address and any other information such as the Subnet mask and Gateway.
  5. Click on Save to save changes.

What does a ProCurve Switch do?

The HP ProCurve 1410-8G, 1410-16G, and 1410-24G Switches are multiport switches that can be used to build high-performance switched workgroup networks. These switches are store-and-forward devices that offer low latency for high-speed networking.

How do I factory reset my HP 1810 24G?

How to Reset a HP 1810-24G to Factory Defaults

  1. Using a paperclip, simultaneously press the Reset and Clear buttons.
  2. Release the reset button, while continuing to press the Clear button.
  3. When all three mode LEDs (Act, FDx, and Spd) begin to blink, release the Clear button.

How do I access my HP switch?

On the computer connected to the new HP Switch you need to: Open a browser software, enter the IP address of your Switch and access the HP Switch web interface. On the prompt screen, enter the administrative login information. After a successful login, the administrative menu will be displayed.

How do I configure my HP switch?

How to: Configure a HP ProCurve switch

  1. Step 1: Connect your serial connection.
  2. Step 2: Conenct PuTTY.
  3. Step 3: Get the IP address.
  4. Step 4: Set time server.
  5. Step 5: Set SNMP community info.
  6. Step 6: Launch the web GUI.
  7. Step 7: Configure basic info.
  8. Step 8: Create VLANs.

How do I reset my HP v1910 24G switch?

Steps I took so far;

  1. Connect switch cable to COM.
  2. Open Putty on COM 38400 – 8 – 1 – N.
  3. Powercycle the switch.
  4. Press Ctrl-B at boot to enter extended boot menu.
  5. Skip current system configuration.
  6. Reboot.

How do I reset my HP 24G switch 1920?

To execute the factory default reset on the switch, perform these steps:

  1. Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
  2. Continue to press the Reset button until the Fault LED light begins to flash.
  3. Release the Reset button.

How do I find my switch IP address?

How to Find a Network’s IP Address Info

  1. Select the Start button located in the bottom left corner.
  2. Type Run into the Start Menu search and press Enter.
  3. Type CMD and press Enter.
  4. Type ipconfig/all and press Enter.
  5. Your network’s IP information should now be displayed in a list.

Does switch have IP address?

When computers are on the same IP segment, it means that the computers belong to the same network. But since the switch does not have the capability to assign IP addresses, the computers connected to it will not be able to communicate with each other. They will get an Automatic Private IP Address (APIPA).

How do I log into my HP switch?

How do I reset my HP switch to factory settings?

To execute the factory default reset on the switch, perform these steps:

  1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
  2. Continue to press the Clear button while releasing the Reset button.
  3. When the Self Test LED begins to blink, release the Clear button.

How do I find the IP address of a connected switch?

To determine the IP address, go to the Layer-3 device that you switch is connected to. In the Layer-3 device ( mostly a router or layer 2.5 switch ) run the “show ip arp” command. And there it is ! You will find the ip address matching with your client’s MAC address.

How to mount the HP ProCurve 1410-24g switch?

Wall Mounting Template for HP ProCurve 1410-24G Switch Screw-hole position for mounting 83.95 mm 3.31 Inch 150.00 mm 5.91 inch (Under-table mounting) After installation, prevent switch movement by placing a third screw along this side. QSG-1410-24G-Feb2010.fm Page 4 Thursday, February 11, 2010 3:21 PM

Where do I plug in the 1410-24g switch?

For the 1410-24G Switch, plug the included power cord into the switch’s power connector and into a nearby AC power source. 2-16 Installing the Switch Installation Procedures

Who is the manufacturer of the 1410-16g switch?

1410-16G Switch DECLARATION OF CONFORMITY according to ISO/IEC 17050-1 and EN17050-1 Supplier’s Name:Hewlett-Packard Company DOC#: RSVLC-0907_01072010 Supplier’s Address: 8000 Foothills Blvd. Roseville, CA 95747-5502 U.S.A. declares, that the product Product Name2:HP ProCurve 1410-16G Switch Product Model(s):J9560A

How many RJ-45 ports are there in 1410-24g switch?

■8, 16, or 24 auto-sensing 10/100/1000Base-T RJ-45 ports with Auto-MDIX. ■1410-24G Switch includes two dual-personality uplink ports (1000Base-T RJ-45 or mini-GBIC). ■Plug-and-play networking—all ports are enabled—just connect the network cables to active network devices and your switched network is operational.