What is Super Diamond Clear used for?
SUPER DIAMOND CLEAR is a solvent-based curing and sealing compound specially designed to cure new concrete, assuring proper cement hydration and strength gain, while providing a non-yellowing seal to protect and enhance the appearance of concrete.
How long does Super Diamond clear last?
3 years
Super Diamond Clear can also be tinted with Euclid Universal Color Packs (EUCO Packs), which are available in 33 standard colors. See the EUCLID UNIVERSAL COLOR CHART for available colors. 3 years in original, unopened container.
How long does it take for Super Diamond clear to dry?
Protect freshly coated surfaces from rain or heavy fog for a minimum of 12 hours after application. Backrolling must immediately follow spraying, as this product dries quickly.
How do you remove Super Diamond Clear?
Dried, cured SUPER DIAMOND CLEAR may be removed with a strong solvent such as EUCO SOLVENT, xylene/xylol, or MEK (always follow package directions and warning labels). EUCO CLEAN & STRIP is a citrus-based stripper that can also be used to remove this product.
What kind of sealer do I use on stamped concrete?
Acrylic sealers
How to choose the best sealer for stamped concreteThe primary type of sealer used for exterior stamped concrete flatwork is a solvent- or water-based acrylic. Acrylic sealers are easy to apply, economical, and most important, breathable, allowing moisture in the slab to escape.
When should I apply clear diamond?
The best time to apply this product is on a cool, overcast day when the temperature is 50°F to 80°F (10°C to 27°C) and is not expected to rise above 85°F (29°C) during application and drying time. Keep Diamond Clear 350 cool before applying.
What is better water-based or solvent-based concrete sealer?
Water-based sealers have a lower level of VOC (volatile organic compounds) content than a typical solvent-based sealer. This means it is less harmful to the person using the product, as well as the environment.
How long do you have to stay off concrete after sealing?
Typically, it can take anywhere from 10-12 hours to dry before being able to be walked on, but they will continue to harden for up to 48 hours after being applied. Concrete sealed with a urethane coating should not be walked on (with the exception of a recoat), driven on, or wet for at least 36-48 hours.
Does Xylene hurt concrete?
Keep in mind, if your concrete was stained or dyed using Xylene, it can damage or change the color of the concrete. If you want to add a new solvent-based sealant, you can just apply the new solvent directly unto the concrete without having to go through removing the old sealer.
How do you keep stamped concrete shiny?
Always apply antiskid every time a new coat of sealer is applied. This will prevent the glossy floor from being slippery when wet. Do not drain gutters on top of your stamped concrete. The constant water and the minerals in the water can breakdown the sealer and permanently stain the surface of the concrete.
How do you make stamped concrete shiny?
After you stain your concrete floor with the color of your choice, you should apply a concrete sealer. A glossy sealer creates a shiny surface, and an acrylic wax adds an additional protective coat.
What is Diamond Clear?
DIAMOND CLEAR is an acrylic co-polymer curing and sealing compound designed to provide a quality cure and seal while assuring total resistance to yellowing from ultraviolet exposure.
How do you remove Diamond Clear 350?
Dried, cured DIAMOND CLEAR 350 may be removed with a strong solvent such as EUCO SOLVENT, xylene/xylol, or MEK (always follow package directions and warning labels). EUCO CLEAN & STRIP is a citrus-based stripper that can also be used to remove this product.
Is one coat of concrete sealer enough?
How many coats should I apply? Two coats are always suggested because the first coat of any concrete sealer is usually absorbed into the concrete at different rates leaving the substrate unevenly sealed. A second coat will ensure proper even coverage.
How long do you leave xylene on concrete?
Take a small amount of Xylene and place it on the area that is still covered with the sealer and let it stand for 20 seconds. Remove any excess Xylene and touch the area.
Should you mix xylene with concrete sealer?
The best way to apply xylene is by flooding it onto the surface with an industrial metal pump-up sprayer. If enough is applied, the xylene should melt the sealer through to the surface of the concrete before it evaporates. In conclusion, applying xylene is a great, inexpensive way to rejuvenate dull or whitened sealer.