How do you use Sansin SDF stain?
When applying exterior Sansin coatings we recommend completely saturating the surface with product to the point where it will absorb no more. This will naturally cause the product to slightly run. Then, as per Directions For Use, back brush the surface to eliminate any streaking by spreading the runs and drips evenly.
How long does it take for Sansin stain to dry?
1 hour
of Sansin extender. Allow 1 hour for drying in proper conditions when the temperature is 70°F (21°C) and the relative humidity is higher than 50%. For deeper color request a stronger formula from your dealer. When using a tinted product be sure to stir well before and during application.
How do I use Sansin ENS?
Use Sansin cleaner and/or wash the entire surface with a minimum 3000 PSI pressure washer using clean water. Sand the surface well using 60-80 grit paper and random orbital sander. Follow by power washing, vacuuming or using compressed air for proper cleaning.
How do you remove Sansin stains?
Dissolve the bag of Sansin Wood Lightener® in 1.5-2 gallons (5.75-7.5 L) of water, depending on the degree of brightening you require. Spray the Sansin Wood Lightener® evenly on cleaned wood surface. Allow the Sansin Wood Lightener® to neutralize the treated wood surface for at least 10 minutes. Rinse off with water.
Is Sansin a good stain?
Sansin SDF and Dec both deliver a beautiful low-lustre finish that is easy to maintain and highly breathable. For a higher-lustre finish – and extreme UV protection – use Sansin ENS as a standalone system or as a topcoat.
Is Sansin SDF water based?
Thanks to SDF’s unique water-borne technology, it can provide complete protection in just one coat – although a second coat will provide an even more beautiful and richer finish. And because SDF is designed to be highly water-repellent, it’s a natural choice for homes and structures in moisture-rich environments.
How do you wash Sansin wood?
Simply spray your wood surface, allow to sit for up to 20 minutes, rinse off and let dry. Then apply the attached package of Sansin Wood Lightener – and watch as the beautiful natural color of your wood emerges as it dries.
Is Sansin stain oil based?
Sansin Enviro Stains use water, not oil, to deeply penetrate and protect wood naturally, from within.
Is Sansin SDF oil based?
Sansin’s modified natural oils and resins are impregnated with special UV protectants so every exposed cell of your wood is protected. Because of their unique formulation, Sansin Enviro Stains also protect naturally against wood decay.
How do I use Sansin in December?
Use Sansin cleaner and/or wash the entire surface with a minimum 3000 PSI pressure washer use clean water. Sand the surface well using a 60-80 grit paper and a variable speed orbital sander. Follow by power washing, vacuuming or using compressed air for proper cleaning.
What is the best temperature to stain a deck?
The Goldilocks Zone for Staining Your Deck
- It’s below 90 degrees Fahrenheit.
- It’s above 50 degrees Fahrenheit.
- It’s a cloudy day or at the right time that the deck is in the shade.
- The humidity is low.
- Rain isn’t in the forecast.
- The wind is calm.
How long should you wait to put on a second coat of stain on a deck?
For best results, avoid staining at midday or in direct sunlight. If a second coat is required, wait 4 hours between applications. Depending on temperature and humidity, allow 24 – 48 hours of dry time before using your beautifully restored deck or porch.
Will a second coat of stain make it darker?
Apply a second coat of stain after the first has dried fully. This will usually produce a darker coloring, but it adds a step to the process and slows production. Substitute a glaze or gel stain for the liquid stain. Glazes and gel stains usually contain a higher ratio of pigment.
How long should I wait between coats of stain?
How Long to Wait Before Second Coat of Stain. Wait an hour before applying a second coat of standard wood stain. You may need to wait for longer for gel stains—about six to eight hours before adding a second coat. In any case, the product label should always indicate how long for stain to dry before the second coat.
What happens if you let stain dry without wiping?
When applying a wood stain, you need to let it sit on the surface enough to color it, but wipe it off before it dries. Leaving the stain on without wiping the excess will result in too much strain on wood and a sticky mess that never dries.
What is Sansin wood treatment?
Sansin wood treatments, finishes and preservatives use water, not petroleum solvents, to deeply penetrate and protect wood naturally, from within. Headquartered in Ontario, Canada, Sansin has dealer locations in Canada, the U.S. and Europe. To learn more about The Sansin Corporation, or how to become a Sansin preferred dealer, visit www.sansin.com.
What is Sansin SDF finish?
Sansin SDF: A penetrating one-coat finish for exterior wood. Penetrating one-coat finish for wood siding. Sansin SDF provides tough, effective protection for wood siding.
What is Sansin purity 0 VOC gel stain?
Category: Products. Sansin Purity 0-VOC Gel Stain: Penetrating gel stain for wood interiors. Beautiful Ultra Low VOC penetrating gel stain for wood interiors.
Where are Sansin dealers located?
Headquartered in Ontario, Canada, Sansin has dealer locations in Canada, the U.S. and Europe. To learn more about The Sansin Corporation, or how to become a Sansin preferred dealer, visit www.sansin.com.