What is AWWA Class D flange?

Table of Contents

These AWWA Class D Steel Ring Flanges meet AWWA C207 specifications and comply with ANSI #150 bolt pattern requirements. At atmospheric temperature, this slip-on style flange is pressure rated to 175psi for 4- to 12-inch flanges, and 150psi for flanges 14 inches and larger.

What is AWWA C207 D?

Awwa C207 Class D Slip On Flange is commonly used in waterworks, slurry, waste water, plant piping or other light duty applications. Generally, the required pressure for the Awwa C207 Class B Blind Flange is less than 300 psi.

What is Class D flange?

This AWWA Class D Steel Blind Flange is manufactured to AWWA C207 and ANSI #150 drill pattern specifications and is intended to seal off piping systems. At atmospheric temperature, this series is pressure rated for up to 175psi for 4- to 12-inch flanges, and 150psi for flanges 14 inches and larger.

What is AWWA C110?

AWWA C110-12 Ductile-Iron and Gray-Iron Fittings (PDF)

What is AWWA C208?

Description / Abstract: AWWA C208, 2017 Edition, June 11, 2017 – Dimensions for Fabricated Steel Water Pipe Fittings. This standard provides formulas to calculate overall dimensions of fittings for steel water transmission and distribution facilities.

How do you measure the thickness of a blind flange?

The equation of calculating the thickness of blind flange as derived from ASME code, Section VIII, Div. 1, is: T = d [C P/S E + 1.9 W hG/S E d3]0.5 , for nomenclature see UG-34(c)(2) and Fig. UG-34 Sketch (j).

How is a flange measured?

MEASURING A STANDARD FLANGE Measure across the centre from one side of the internal hole to the opposite side of the hole. Measure across the centre from the external edge to the other external edge of the flange. Measure from centre of the bolt hole to centre of the opposite bolt hole.

What is AWWA fitting?

AWWA size fittings are supplied with rigid radius grooves in accordance with ANSI/AWWA C-606. Fittings conform to ANSI 21.10/AWWA C-110 for center-to-end dimensions and AWWA C-153 or ANSI 21.10/AWWA C-110 for wall thicknesses. Available with a wide variety of coatings and linings.

How do you calculate the thickness of a spade?

As a rule of thumb the following formula can be used to calculate the thickness in millimeters..

Pressure (barg) multiply by diameter (inches) divided by 10.
Pressure.. the highest pressure that the system can achieve.
Diameter.. the size of the spacer in inches.
Example.. 8 x 12 / 10 – thickness of spacer = 9.6 mm.

What is the diameter of a flange?

A typical flange should be 3-4 millimeters larger than the nipple diameter and the average flange diameter is between 24 and 27 millimeters.

How do you pick a blind flange?

When choosing blind flanges, you must consider the best flange material and dimensions in relation to the piping standards and requirements of your intended application. Generally, your flange material should match the connecting pipe material. The most common blind flange materials are steel and stainless steel.

How many types of blind flanges are there?

The most common two types are the flat face (FF) and the raised face (RF) blind flange.

How are flanges measured?

What is the pressure rating for AWWA C207 flanges?

AWWA C207 Flange rating range from the Class B flange rated at 86 psi to Class F flanges, both rated at 300 psi. AWWA C207 Class D flanges are by far the frequently specified among AWWA C207-94 Flange users, and carry a pressure rating of 175 psi for sizes below 12″, and 150 psi for sizes 12″ and larger.

What is C207 Class D steel blind flange?

We manufacture the AWWA C207 Class D Steel Blind Flange, which is mainly used to seal off the piping system. These are primarily used in slurry, wastewater, waterworks, and plant piping industries- these flanges are for light-duty works. For the sizes below 12 inches, the Awwa C207 Class E-Hub Flange carries a pressure rating of around 175 PSI.

What is the tensile and yield strength of the AWWA C207 gasket?

Minimum Tensile for the Awwa C207 Class D Gasket is about 50,000 psi, while the minimum Yield strength of the Awwa C207 Class E Flanges is upto 32,000 psi.